USB, UART & Serial Adapter Guide

RACCLABS FIELD GUIDE / SERIAL INTERFACES

USB, UART, TTL & FTDI — decoded.

Pick the right adapter for the job. Understand what the chip does, what the pins mean, and what voltage your target board expects before you connect anything.

Shop serial adapters & bench tools

First: these words are not interchangeable

USB
The computer-side connection. A USB-to-serial adapter makes a USB device appear as a serial port to your computer.
UART
A serial communication method: transmit (TX), receive (RX), and usually a shared ground. UART describes how bits are framed and sent, not the voltage standard.
TTL-level serial
Common hobby shorthand for logic-level UART signals. Modern boards are usually 3.3V; older boards may use 5V. Confirm the actual I/O voltage.
FTDI
A company and a family of USB-interface chips. FT232-series chips commonly bridge USB to UART. FTDI is not a different serial protocol.
RS-232
A different electrical interface with positive and negative voltages and inverted signaling. A TTL UART adapter cannot connect directly to an RS-232 port; use a proper RS-232 transceiver such as a MAX3232-based converter.

Which USB-to-UART chip should I choose?

Bridge chip Best fit What to know
FT232RL / FT232RN Established FTDI ecosystem, serial consoles, development and troubleshooting FT232RL is an older part marked NRND by FTDI; check the exact chip and board. FT232RN is the newer revision family. I/O voltage depends on VCCIO and adapter design.
CP2102 / CP2102N Everyday ESP32, Arduino-style boards, GPS and embedded UART work Widely used and usually a strong value. CP2102 and CP2102N are not identical parts; board pinout, regulator and logic voltage still matter.
CH340G / CH340C Low-cost development boards and basic serial consoles Often the budget option. CH340G typically uses an external crystal; CH340C includes an internal clock source. Verify the exact variant and driver.

The chip name alone does not guarantee a safe 3.3V or 5V interface. The adapter board determines its pinout, voltage selection, regulator capacity and exposed signals.

Choose the right connection

  • 3.3V target: use a 3.3V UART logic adapter. Typical examples include ESP32, ESP32-C3/C6/S3, many GPS modules and modern microcontrollers.
  • 5V target: use a 5V-compatible UART interface only when the target's documentation confirms 5V logic.
  • Unknown target: stop and identify its voltage and pinout first. Do not guess based on connector shape or wire color.
  • RS-232 equipment: use a USB-to-RS-232 adapter or a UART adapter plus a suitable RS-232 transceiver. TTL UART is not RS-232.
  • Power: TX/RX adapters may expose 3.3V or 5V power pins, but those pins are not automatically safe to power the target. Check current limits and avoid connecting two power sources together.

Basic UART wiring

Adapter TX→Target RX

Adapter RX←Target TX

Adapter GND—Target GND

TX and RX cross over. Ground is shared. Leave VCC disconnected unless you intentionally need to power the target and have verified the adapter's output voltage and current capability. Never connect a 5V TX signal to a 3.3V-only input without proper level shifting.

What about DTR, RTS and boot pins?

Some adapters expose DTR and RTS in addition to TX/RX. Certain development boards use these control signals with reset circuitry for automatic bootloader entry. A basic three-pin adapter may still work, but you may need to enter boot mode manually. Check the target board's documentation before wiring control pins.

Before you order: quick compatibility checklist

  1. Identify the device model and its serial interface: TTL UART or RS-232?
  2. Confirm the target's I/O voltage: 1.8V, 3.3V or 5V?
  3. Check connector and pin order: header pitch and TX/RX/GND/VCC labels vary.
  4. Decide whether you need only TX/RX/GND or also DTR/RTS.
  5. Check whether your operating system needs a driver for the specific bridge chip.

Not sure which adapter you need?

Send us the device model, a clear photo of its connector or pin labels, and your computer's operating system. We'll help identify the interface before you order.

Ask RaccLabs about compatibility

RaccLabs rule: understand the interface before applying power. A $5 adapter should not become a $50 repair.